. Uncompress the file. Double-click on 'Install.exe' to install the drivers. Plug cable into any computer's USB port. 'Found New Hardware Wizard' will start and it will ask you 'Can Windows connect to Windows Update to search for the software?'

1. Vag Com 409.1 Activation File

Select 'Yes'. Select 'Install the software automatically'. After the installation is complete, click 'Finish'. 'Found New Hardware Wizard' will start once again because there are two drivers for this cable.

Go through the same steps as explained above to install this second driver.If install is successful, move onto Step 2.If installation fails, see below: Troubleshooting: If Drivers Failed To Install. Installation failed?.Unextract the file into any folder. Then while your cable is connected to the computer — go Device Manager. Windows Vista/7/8/10: Control Panel » System » Device Manager. Windows XP: Control Panel » System » 'Hardware' tab » Device ManagerYou'll see a device similar to 'USB Serial Port' under either 'Other devices' or 'Ports (COM & LPT)'.Right-click and choose 'Update Driver Software'. Like this:Then select the location where you unextracted Driver Pack 2. Let it install.

STEP 2: Discover Port Number that VAG-COM KKL Cable is UsingGo to Control Panel. Windows Vista/7/8/10: Control Panel » System » Device Manager. Windows XP: Control Panel » System » 'Hardware' tab » Device ManagerExpand 'Other devices' or 'Ports (COM & LPT)'. Whichever contains 'USB Serial Port'.Next to 'USB Serial Port' — you'll see a number.If the COM port number is between 1-4, then everything is fine. Move onto Step 3.If the COM port number is above 4, then we'll have to change it so it's between 1-4.

Here's how.Right-click on 'USB Serial Port' and click on 'Properties' — as per below pic:Then:. Click: Port Settings. Click: Advanced. For 'COM Port Number' — you MUST choose any number between 1-4.That's it! Now let's test if everything is working.

Vag Com 409.1 Activation File

Move onto next step below. STEP 3: Test Everything is WorkingCable should be plugged into computer. Start VCDS-Lite software. Click 'Options' button. You will see 'Select COM Port' box. Select the 'COM Port' number as explained in Step 2. Click the ‘Test’ button.

If everything is good, it should display 'Interface Status: Found!' . You can now connect other end of cable to car.

Turn on ignition. And you're ready to start diagnosing!If test is not successful — check the following:. Other software or devices using USB ports or that same COM Port could be conflicting. You should uninstall the suspected software or device for troubleshooting this problem.

It should be noted that VAG-COM 409.1 KKL cable does not work on vehicles running on CAN-BUS System. Cable must be plugged into the vehicle with ignition ON.

Test the cable with each COM Port from 1 to 4 in Windows Device Manager. Make sure that the driver is installed and configured as explained in Step 1. More Troubleshooting Tips:.

Only Audi, Volkswagen, Skoda and Seat vehicles are supported. Other brands will only work for generic OBD-II functions. If VAG-COM 409.1 KKL cable doesn't connect — or if you get the error message 'Can't Synch Baud Rate' — then go to Options and set Start Baud to 9600.

If 9600 doesn't work, try 4800 and 1200. Turn the vehicle's ignition OFF and back ON after each failed attempt to connect.

If you have installed VCDS software before or from another source, uninstall all versions of VCDS software right now, and delete directory 'C:Ross-Tech'. Then install latest version of VCDS-Lite software by clicking.For further information and instructions for troubleshooting, visit the following links:.

(, 04:25 PM)brajomobil Wrote: (, 08:30 PM)saabdoctor Wrote: when i run the crack on vag com 409.1 it says its activated but when i try to actually use vag com it says its not activated- any ideas? Tried a few times, same result.Install 409 and connect to car, then disconnect from car close program then crack.Start cracked version. That is it.followed your instructions to the letter but still the same, initially seems to work and it says its registered but as soon as i try to use a feature that needs registration it slips back into unregistered mode. Any ideas anyone?saabdoctor.